Current Location:Home >  Products >  YASUDA rapid cold-pressing production line
Product Category
Floor Equipment
Building materials equipment
Automatic production line
YASUDA rapid cold-pressing production line
Address: Zhangjiawan Development Zone,Tongzhou,Beijing,China
Postal code: 101103
E-mail:azumi@vip.163.com My status msn:azumi@vip.163.com
YASUDA rapid cold-pressing production line
Equipment Introduction

   Japanese YASUDA rapid cold-pressing production line without formaldehyde glue was set up in the end of 80’s in Japan. After more than 30 years’ development, its mature cold-pressing technology had developed into the leader of pressing technology for Japanese wood floor, wooden door, and wood-packaged aluminum window etc completely, and had been promoted in overseas. It came to China in 2008. Cold-pressing technology for floor refers to that as the surface floor and core materials are pressed under normal temperature during producing, pressing under normal temperature is the ideal choice of pressing technology. Based on such idea, YASUDA Company had developed this kind of production line which is applicable for cold-pressing technology; in addition, it had obtained equipment patents and technology patent certificate issued by Japan Patent Office.

    Full automatic non-formaldehyde glue cold-pressing production line refers to the realization of full automatic production mode of floor and wooden door in material feeding preheating, gluing, flitching, cold-pressing and packaging of core material, surface board and back board when being produced. Such production mode can finish a cyclic pressing within 15 – 45 seconds, realizing intensive production, unmanned management, costs reduction and brand awareness promotion.

1. The pressing finished by cold-pressing technology will not lead to board bending due to the redistribution of water produced by hot-pressing inside the wood materials.

2. The pressing time has nothing to do with the thickness of surface board and back board. The (0.6-6) mm veneer can be pressed within 15 – 45 seconds.

3. Such technology is applicable for double-faced pressing. For three-layer composite floor or long board more than 1200mm, back pressing can prevent board side bending. Double-faced pressing has become the development tendency of high-class floor.

4. For the preheating principle of YASUDA equipments, it is core material preheating, and no heat treatment has been done on surface board, while some equipments dry surface board and glue via shining, which will reduce the moisture contents in surface board instantly and lead to crack produced on the surface after painting.

5. The adoption of non-formaldehyde cold-pressing glue, Japanese technology, fully environment-friendly, meet with European E0 standard.

6. Production efficiency is high, and a cyclic processing can be completed within 15 – 45 seconds.

 

 

 

 

Equipment Photos











  • Equipment Videos
    Equipment Parameters

          1. Name:

    :Japanese YASUDA Rapid Cold-pressing Line

           2. Power

     

     

     

     

     

                   Power supply:

     

    : Three-phase  AC380V    50Hz、Total power: 95KW

                   Operating voltage: Single-phase

     

    :Single-phase   AC200V    50Hz

                   Compressed air

     

    :0.5MPa,200L/min(ANR)・・・2个

           3. Parameters

     

     

     

     

     

            3.1 Dimension of pressing board materials

     

     

     

                     (1)Core materials

     

     

     

     

     

                     Width

     

     

    70~1000mm

     

                        Length

     

     

    500~2450mm

     

                      Thickness

     

     

    8~25mm

     

     

                     (2)Surface board

     

     

     

     

     

                     Width

     

     

    70~1000mm

     

                        Length

     

     

    500~2450mm

     

                      Thickness

     

     

    2~6mm

     

     

            3-2.①Hydraulic thermocompressor

     

     

     

                      Model

     

     

    M1-2400H

     

                       Dimension of hot pressboard

     

    1100W×2600L mm one set for the upper and lower

                      Pressure

     

     

    30~254kN(3~25ton)

                        Oil pressure installation

     

    3.7KW,160L, oil tank attached

                        Hot source

     

    Vapor, above 1.0MPa

     

                      Transmission part of feeding

     

    Belt transmission + Chain

     

                        Chain

     

    0.75KW

                        Feeding speed

     

    34m/min

     

     

             3.3 ② Double-faced full automatic gluing machine + mixer

     

     

                      Double-faced full automatic gluing machine

     

     

     

                     Model

     

     

    ATZ-130/Y

     

                       Upper and lower rubber roller

     

    φ255×1370L、 composite rubber, 16 groove/ inch, single-driven

                     Upper and lower running roller

     

    φ150×1370L、 stainless steel pipe, single-driven

                     Driven motor per roller

    0.75KW×4P、4sets

     

                     Feeding speed

     

    40m/min

     

     

                        Driven roller at feed inlet

     

    φ60×1525L、rust-proof treatment

                       Full automatic mixer

     

     

     

     

                     Model

     

     

    AGS-75/Z

     

                        Mixing motor

     

    1.5KW(change speed via frequency changer)

     

                     Oiling equipment

     

    0.75KW(change speed via frequency changer)

                        Mixing capacity

     

    50L

     

     

              3-4.③Alternative transport unit

     

                      Model

     

     

    SBF -2450

     

                     Feeding roller

     

    φ68×1t, resin block, 50P, roller interval 200mm

                        Driven motor

     

    0.4KW

     

     

                        Feeding motor

     

    40m/min

     

     

              3-5.④ 250ton cold-pressing machine

     

     

     

                      Model

     

     

    M1-2400C

     

                       Dimension of hot pressboard

     

    1100W×2600L mm, one set respectively for the upper and lower

                      Pressure

     

     

    300~2637kN(30~250ton)

     

     

     

    Effective pressurizing area: 1000×2500mm, max10kg/cm2

                        Oil pressure installation

     

    7.5KW,400L oil tank attached

                      Driven part of feeding

     

    Type of middle-part transport feeding platform

     

                        Middle transfer feeding table

     

    1.5KW、1100W×    L

                        Feeding speed

     

    34m/min

     

     

     

     

     

     

     

     

              3-6.⑤ Transport unit of ejection after finishing pressing 

                      Model

     

     

    BC-1000×2500

     

                       Feeding motor

     

    0.75KW×4P、

     

                        Feeding speed

     

    34m/min

     

     

                       Feeding belt

     

    1000W×